BuyFromBest

Pressure Washer Soap Injector Not Working? 8 Fixes

Some links in this guide are affiliate links. If you buy through them we may earn a commission, at no extra cost to you. This never affects what we recommend or how we rank equipment. Read our disclosure.

A pressure washer soap injector not working is usually one of five things: the wrong nozzle, a discharge hose that is too long, a clogged screen or chemical line, an air leak, or a stuck check ball in the injector. A downstream injector only pulls soap when the system drops to low pressure, so the first check is always the nozzle. Work through the list below in order; most of the fixes are quick and need no parts.

Quick answer

Fit the black low-pressure soap nozzle, because a downstream injector only draws in low-pressure mode. Make sure the screen sits at the bottom of the soap container, the chemical hose is not kinked, and the screen, hose and injector are not clogged. If it still will not draw, shorten the discharge hose, check for air leaks in the chemical line, thin very thick chemical, and clean or rebuild the injector’s check valve.

How a downstream soap injector works

A downstream injector sits after the pump, in the high-pressure line. It has a small orifice that creates suction when water flows through it fast at low pressure, and that suction pulls detergent up through the chemical hose. General Pump’s Hi-Draw injectors, for example, are rated to 4,500 PSI and draw up to 20% chemical.

The catch is in General Pump’s installation note: for proper operation, “a control device such as a dual lance wand, quick couple nozzles, or an adjustable nozzle holder must be used to lower the system pressure at the nozzle.” At full spraying pressure, the injector does not draw. That is why the nozzle is the first thing to check.

Step-by-step: why your pressure washer is not pulling soap

  1. Check the nozzle. Simpson says to “make sure you have the black, low-pressure soap nozzle attached to the wand,” because injection only works with that nozzle. On a dual lance or adjustable wand, switch it to low pressure. General Pump lists “incorrect nozzle” and “system is not in low pressure mode” as the first two causes.
  2. Check the screen. The filter screen on the end of the chemical hose must sit at the bottom of the soap container. Simpson warns that “if it floats on top, the chemical will not be drawn into the system.”
  3. Check the chemical hose. Untangle and straighten it so it is not kinked, as Simpson advises, and look for cracks.
  4. Clear clogs. Dried chemical can block the screen. Simpson says to put the screen in clean water and draw the water through with the soap nozzle, and to clean or replace it if it is clogged. General Pump lists a clogged chemical line as a cause and says to clear the obstruction.
  5. Shorten the discharge hose. General Pump says a discharge hose that is too long stops the injector drawing or slows the draw rate. The fix is a shorter hose or a different injector sized for your setup.
  6. Look for air leaks. A loose fitting or split in the chemical line lets the injector pull air instead of soap. General Pump lists an air leak as a cause of slow draw.
  7. Thin thick chemical. If the detergent is very viscous, General Pump says to reduce it with water to lower its viscosity. Follow the chemical label’s dilution range.
  8. Clean or rebuild the injector. Inside the hose barb is a small check valve: a stainless ball, a spring and an O-ring. Dried chemical can jam the ball. General Pump’s fix for an obstruction in the check valve is to take it apart and remove it, and to replace a damaged O-ring. Its repair kit 100803 contains the spring, ball and O-ring.

Injector problems and fixes at a glance

ProblemLikely causeFix
Injector will not draw at allWrong nozzle or not in low pressure modeFit the black soap nozzle or switch the wand to low pressure
Injector will not draw at allDischarge hose too longUse a shorter hose or a different injector
Injector will not draw at allClogged chemical line or screenClear the line, soak and flush the screen
Draw is too slowAir leak in chemical lineFind and repair the leak
Draw is too slowChemical too thickDilute with water within the label range
Chemical leaks from the hose barbObstruction or damaged O-ring in check valveClean the valve, replace the O-ring
Pump, motor or engine laborsClogged injector or wrong orifice sizeClear the orifice or fit the correct injector

This table follows General Pump’s troubleshooting chart for its Hi-Draw injectors. The last row matters on commercial machines: an injector whose orifice is too small for the pump’s flow adds load, so match the injector to your machine’s GPM. General Pump sells versions for 1 to 2, 2 to 3, 3 to 5 and 5 to 8 GPM.

How to keep a soap injector working

  • Flush after every use. Simpson’s method works as a habit: drop the screen in a bucket of clean water and run it through the soap nozzle for a minute so no chemical dries in the injector.
  • Do not use bleach. Simpson warns never to use bleach in its systems, because it can release chlorine gas and damage internal components.
  • Use chemicals the injector is rated for. General Pump says its injectors are for clean, fresh water, and to contact its technical service for corrosive liquids; it offers an optional acid kit with a ceramic ball.
  • Check the spray in low pressure. If you see foam or color at the nozzle within a few seconds of switching to the soap tip, the injector is drawing.
  • Do the rest of the routine maintenance. While you are at it, check the pump oil; our pressure washer pump oil guide lists the oil and interval each pump maker specifies.

If the machine has also lost pressure on the rinse setting, the problem may be in the pump or unloader rather than the injector. Our guides to a pressure washer losing pressure and adjusting an unloader valve cover those. For which nozzle does what, see our pressure washer nozzle chart.

Parts we would buy

General Pump 100775 downstream chemical injector, 3 to 5 GPM
Injector

General Pump 100775 downstream chemical injector, 3 to 5 GPM

For 3 to 5 GPM machines. Pick the GPM range that matches your pump.

Check price on Amazon
Karcher 65 degree soap nozzle, quick connect, up to 4000 PSI
Soap nozzle

Karcher 65 degree soap nozzle, quick connect, up to 4000 PSI

Low-pressure soap tip; check it matches your wand's quick-connect size.

Check price on Amazon

As an Amazon Associate we earn from qualifying purchases. Prices and availability change, so check the current price on Amazon.

Common questions

Why is my pressure washer not picking up soap?

Usually because the black low-pressure soap nozzle is not fitted, so the system never drops to low pressure. Other common causes are a clogged screen, a kinked chemical hose, a discharge hose that is too long, or a stuck check ball in the injector.


Why is my downstream injector not pulling?

General Pump lists an incorrect nozzle, the system not being in low-pressure mode, a discharge hose that is too long, and a clogged chemical line. Check them in that order.


How do I unclog a pressure washer soap injector?

Put the screen in clean water and draw it through with the soap nozzle. If that fails, take the injector’s hose barb apart and clean the check ball, spring and O-ring, or fit a repair kit.


Does hose length affect a soap injector?

Yes. General Pump says a discharge hose that is too long can stop the injector drawing or slow the draw rate. Use a shorter hose or an injector suited to the setup.


Which nozzle do I use for soap on a pressure washer?

The black low-pressure soap nozzle, or the low-pressure setting on a dual lance or adjustable wand. Downstream injectors only draw in low-pressure mode.


Can I put bleach through my pressure washer soap injector?

Simpson says never to use bleach, because it can release chlorine gas and damage internal components. Use detergents made for pressure washers and the injector.

Bottom line: fit the soap nozzle first, then check the screen, the chemical hose and the hose length, and clean the injector’s check valve if it still will not draw.

Mia Reynolds
Written byMia Reynolds

Mia Reynolds is a commercial cleaning equipment service technician with nine years on the repair side of the business. She has torn down and rebuilt floor scrubbers, pressure washers, and industrial vacuums from Tennant, Nilfisk, Karcher, and half a dozen other brands, and has trained in-house maintenance teams on preventive service schedules. At BuyFromBest she writes the troubleshooting and repair content: squeegee streaking, recovery tank suction loss, brush motor faults, unloader valve failures, and the rest of the problems that pull a machine out of service. Her rule of thumb: most equipment failures are maintenance failures that started months earlier.

Questions & comments

Found an error, or have a question about your machine? Leave a comment and we will answer it.

Ask a question or report an error

Your email address will not be published. Required fields are marked *