BuyFromBest

Floor Buffer Pad Color Chart: What Each Color Does

Some links in this guide are affiliate links. If you buy through them we may earn a commission, at no extra cost to you. This never affects what we recommend or how we rank equipment. Read our disclosure.

The floor buffer pad color chart follows one rule: the darker the pad, the more aggressive it is. White and tan pads polish, red pads spray buff and clean lightly, blue and green pads scrub, and brown, black and maroon pads strip finish. Pastel pads in pink, peach or champagne are for high-speed burnishers only. Colors are close across brands but not identical, so check the maker’s chart before you pick.

Quick answer

White or tan: polishing. Red: spray buffing and light daily cleaning. Blue: cleaning and heavier scrubbing. Green: heavy scrubbing or light stripping before a recoat. Brown: dry scrubbing on some charts, stripping on others. Black and maroon: stripping. Pastel colors such as powder blue, peach, pink and champagne: high-speed burnishing at 1,000 to 3,000 RPM. Use the least aggressive pad that does the job.

The floor pad color chart

Pad colorMain useMachine
WhitePolishing, light cleaning with minimal dullingLow speed, 175 to 300 RPM
TanPolishingLow speed
RedSpray buffing, everyday cleaning and light scrubbingLow speed or autoscrubber
BlueCleaning and heavier scrubbingLow speed or autoscrubber
GreenHeavy scrubbing, light stripping before recoatingLow speed or autoscrubber
BrownDry scrubbing (Waxie) or stripping (Hillyard, Tennant)Low speed
BlackStripping, the most common stripping padLow speed
MaroonStripping, the most abrasive of the three Hillyard listsLow speed
Powder blue, peach, pink, champagneHigh-speed burnishingBurnisher, 1,000 to 3,000 RPM
Natural hair blendAggressive burnishing of hard or worn finishBurnisher

The core of this chart comes from Waxie, which lists white or tan for polishing, red for spray buffing, blue for cleaning and burnishing, green for scrubbing or light stripping and recoating, brown for dry scrubbing and black for stripping, and says there is “typically not much variation between manufacturers in the most common colors.” Hillyard and Tennant fill in the stripping range and the burnishing pads.

Darker pads are more aggressive

Pad makers use color to show how abrasive a pad is. Waxie says the pads increase in aggressiveness “as the shades get darker,” and Hillyard says “black pads are the most aggressive and white pads are the least aggressive.”

Waxie’s advice on choosing is the most useful line in any pad chart: “use the least aggressive pad to do the intended task.” A pad that is too aggressive removes more finish than needed, leaves the floor less protected and duller, and can force a full strip and recoat sooner.

Where the brands disagree

The common colors line up, but blue and brown do not mean the same thing everywhere:

  • Blue: Waxie lists blue for cleaning and burnishing. Tennant’s blue cleaning pad is a heavy-duty scrubbing pad that removes 1 to 2 coats of finish before recoating. Hillyard lists blue for general-purpose, medium-duty scrubbing.
  • Brown: Waxie lists brown for dry scrubbing. Hillyard and Tennant both list brown as a stripping pad, with Hillyard calling it the least aggressive of its brown, black and maroon stripping pads and Tennant saying its brown pad removes 2 to 4 coats.
  • Burnishing pads: Hillyard notes burnishing pad colors vary by maker, including blue, beige, gray and black, and natural hair blends. Waxie describes them as typically pastel shades, which reduce color transfer at high speed.

So treat any chart as a starting point and read the description on the pad you are buying, especially for blue, brown and burnishing pads.

Which pad for which machine speed

Pad choice depends on the machine as much as the job. Waxie says basic pads are designed for conventional 175 to 300 RPM machines, and that for high-speed equipment at 1,000 to 3,000 RPM, makers offer matching high-speed burnishing and buffing pads. On a burnisher, use pads the maker rates for high speed rather than standard stripping, scrubbing or polishing pads. Our guide to a floor buffer vs burnisher explains the two machines.

What size floor pad do you need?

Match the pad to the machine’s pad driver. Hillyard says most scrubbing and stripping pads are round and range from 10 to 21 inches across, burnishing pads typically range from 17 to 27 inches, and some orbital scrubbers use rectangular pads about 14 inches on one side and 20 to 32 inches on the other. The size is stamped on the pad driver or listed in the machine manual.

Which pad to use for common jobs

JobPad to start with
Daily cleaning with an autoscrubberRed, or white on soft finish
Spray buffing scuff marksRed
Deep scrub before a recoatBlue or green, depending on the brand chart
Stripping old finishBlack, or brown on uneven floors
Heavy build-up and sealerBlack or maroon
High-gloss burnishingThe burnisher maker’s high-speed pad

For the full process, see our guides on how to strip and wax a floor and how to use a floor scrubber. If you are choosing machines, our commercial floor cleaning machines guide lists which machine does which job.

3M floor pads we would buy (20 inch)

3M Buffer Floor Pad 5100, red, 20 inch, case of 5
Red buffer

3M Buffer Floor Pad 5100, red, 20 inch, case of 5

For spray buffing and daily cleaning under an autoscrubber. Check your pad driver size.

Check price on Amazon
3M Super Polish Floor Pad 4100, white, 20 inch, pack of 5
White polish

3M Super Polish Floor Pad 4100, white, 20 inch, pack of 5

Least aggressive; for polishing and light cleaning.

Check price on Amazon
3M Black Stripper Pad 7200, 20 inch, case of 5
Black stripper

3M Black Stripper Pad 7200, 20 inch, case of 5

For stripping finish with a stripping solution. Not for daily cleaning.

Check price on Amazon

As an Amazon Associate we earn from qualifying purchases. Prices and availability change, so check the current price on Amazon.

Common questions

What do the different color floor buffing pads mean?

The color shows how aggressive the pad is: darker is more aggressive. White and tan polish, red spray buffs, blue and green scrub, and brown, black and maroon strip finish. Pastel pads are for high-speed burnishers.


What color buffing pad should I use on my floor?

Use the least aggressive pad that does the job, as Waxie advises. Red is the usual pad for spray buffing and daily cleaning; white is for polishing soft finishes.


What is the color code for floor pads?

White or tan for polishing, red for spray buffing, blue for cleaning, green for scrubbing, brown for dry scrubbing or light stripping, and black for stripping. Brands differ a little, especially on blue and brown.


What color pad is used for stripping floors?

Black is the most common stripping pad. Hillyard also lists brown, the least aggressive stripper, and maroon, the most abrasive.


What pad do you use on a burnisher?

A high-speed burnishing pad made for 1,000 to 3,000 RPM machines, usually a pastel color such as powder blue, peach, pink or champagne, or a natural hair blend for hard, worn finish.


Can you use a red pad on a floor buffer?

Yes. Red is the standard pad for spray buffing and light cleaning on a low-speed floor machine, and 3M’s red buffer pad also works under an autoscrubber for daily cleaning.

Bottom line: lighter pads polish and darker pads cut, so start with the least aggressive pad for the job, match it to your machine’s speed and size, and check the brand chart for blue, brown and burnishing pads.

Jordan Carter
Written byJordan Carter

Jordan Carter spent twelve years buying and managing cleaning equipment fleets for commercial janitorial contractors across the Midwest, handling everything from single-machine purchases to 40-unit rollouts. He has personally specced, negotiated, and signed off on walk-behind and ride-on scrubbers, industrial sweepers, carpet extractors, and pressure washing rigs from most major manufacturers. At BuyFromBest he writes the buying guides, cost breakdowns, and head-to-head comparisons, focused on what a machine actually costs to own over five years, not just the sticker price. He is especially interested in the gap between what manufacturers claim and what facility managers report after eighteen months of real use.

Questions & comments

Found an error, or have a question about your machine? Leave a comment and we will answer it.

Ask a question or report an error

Your email address will not be published. Required fields are marked *